ARRL guidance on design of ferrite cored inductors

The ARRL handbook for radio communications (Ward 2011) gives guidance on designing with ferrite cored inductors:

Ferrite cores are often unpainted, unlike powdered-iron toroids. Ferrite toroids and rods often have sharp edges, while powdered-iron toroids usually have rounded edges.
Because of their higher permeabilities, the formulas for calculating inductance and turns require slight modification. Manufacturers list ferrite AL values in mH per 1000 turnssquared. Thus, to calculate inductance, the formula is



L = the inductance in mH
AL = the inductance index in mH per 1000 turns-squared, and
N = the number of turns.

Example: What is the inductance of a 60-turn inductor on a core with an AL of 523? (See the chapter Component Data and References for more detailed data on the range of available cores.)


Lets follow the example through. Continue reading ARRL guidance on design of ferrite cored inductors

Antenna half power bandwidth and Q, concept and experimental validation

Many antennas can be represented near their series resonance as a series RLC circuit, and in many cases R changes very slowly with frequency compared to X. This provides a convenient and good approximation for the behavior of the antenna impedance in terms of a simple linear circuit.

Series resonant circuit

The response of a simple series resonant RLC circuit is well established, when driven by a constant voltage source the current is maximum where Xl=Xc (known as resonance) and falls away above and below that frequency. In fact the normalised shape of that response was known as the Universal Resonance Curve and used widely before more modern computational tools made it redundant.

Above is a chart of the Universal Resonance Curve from (Terman 1955). The chart refers to “cycles”, the unit for frequency before Hertz was adopted, and yes, these fundamental concepts are very old. Continue reading Antenna half power bandwidth and Q, concept and experimental validation

AIM system – AIM912 initial checkout

Given that most versions of the AIM software that I have tried have had serious defects, I approach the latest release, AIM912, with caution.

An interesting opportunity presented when a correspondent sent me some .scn files captured from an AIM4170B using AIM912.

Above is the correspondents .scn file opened in AIM912. Continue reading AIM system – AIM912 initial checkout

Review of inexpensive Chinese LAN cable tester

I bought an inexpensive LAN cable tester to give to my daughter.

Above is the sellers pic, the specifications states that it checks data wires 1-8 and the shield / ground connection of STP cables.

On test, it failed to show the shield connection on an STP cable, the LED did not light on either the master or the slave unit.

I tore it apart to see if it was worth getting a replacement. Continue reading Review of inexpensive Chinese LAN cable tester

Speaker tick generator (for polarity testing)

A recent purchase of an inexpensive ($6) speaker polarity tester prompted a need for a stand alone driver for speakers.

Above, the tester has a microphone that senses the polarity of the pressure wave and indicates with one of two LEDs.

The tester comes with a CD containing a file that can be used to provide the test signal on a complete system with CD player, but there is a need for a stand alone driver for testing bare speakers or speaker units. Continue reading Speaker tick generator (for polarity testing)

IMD associated with colorbond sheet steel cladding

A recent experiment exposed significant IMD of a 7MHz locally radiated signal.

The source used for these tests is a battery powered low power transmitter  driving a 0.6m square loop. Radiated power is very low (of the order of -60dBm EIRP), and received signal on the station receiver is less than -73dBm.

Loop near steel shed #1

The loop was leaned against the colorbond sheet steel wall of shed #1. Shed #1 is about 40m from the receiving antenna, and is connected to the power mains. The building has colorbond sheet steel screwed to a steel frame. Colorbond is painted Zinc/Aluminium coated steel.

For this test, the submain was turned off at the main switchboard, so there is not equipment in the shed powered up, but the supply neutral is still connected and bonded to the shed steel work and shed PES ground electrode.

Above, the spectral response of receiver output, there are a number of side products at 100Hz intervals, presumably some form of IMD. At higher radiated power, products at odd 50Hz intervals become visible, though at much lower level than the 100Hz products. Continue reading IMD associated with colorbond sheet steel cladding

Baselining an antenna system with an analyser

I often receive emails from folk trying to validate continued performance of an installed antenna system using their analyser.

With foresight they have swept the antenna system from the tx end and saved the data to serve as a baseline.

The following are example sweeps from one of my own antennas, a Diamond X50N with 10m of LDF4-50A feed line.

Now I have plotted Return Loss rather than VSWR for several reasons:

  • Return Loss is more sensitive to the problems that we might want to identify;
  • Rigexpert in this case decided that the Antscope user could not be interested in plotting VSWR>5 (Return Loss<3.5dB).

Now a hazard in working with Return Loss is that many authors of articles and software don’t use the industry standard meaning.

Return Loss

Lets just remind ourselves of the meaning of the term Return Loss. (IEEE 1988) defines Return Loss as:

(1) (data transmission) (A) At a discontinuity in a transmission system the difference between the power incident upon the discontinuity. (B) The ratio in decibels of the power incident upon the discontinuity to the power reflected from the discontinuity. Note: This ratio is also the square of the reciprocal to the magnitude of the reflection coefficient. (C) More broadly, the return loss is a measure of the dissimilarity between two impedances, being equal to the number of decibels that corresponds to the scalar value of the reciprocal of the reflection coefficient, and hence being expressed by the following formula:

20*log10|(Z1+Z2)/(Z1-Z2)| decibel

where Z1 and Z2 = the two impedances.

(2) (or gain) (waveguide). The ratio of incident to reflected power at a reference plane of a network.

Return Loss expressed in dB will ALWAYS be a positive number in passive networks.

The relationship between ReturnLoss in dB and VSWR is given by the equations:

  • ReturnLoss=-20*log((VSWR-1)/(VSWR+1))
  • VSWR=(1+10^(-ReturnLoss/20))/(1-10^(-ReturnLoss/20))

Diamond X50N on 2m

So now that we are on the same page about Return Loss, lets look at my 2m plot.

The X50N does not have VSWR or Return Loss specs, but we might expect that at the antenna itself, VSWR<1.5 which implies Return Loss>25dB. Measuring into feed line, you can add twice the matched line loss to the Return Loss target (see why Return Loss is a better measure).
Continue reading Baselining an antenna system with an analyser

Thompson’s coax common mode explanation

A recent online discussion on common mode feed line current was directed to Thompson’s article with the recommendation that is ALL basically needed to discuss the common mode current.

Above is Thompson’s diagram of currents in a feed coax, and it contains two significant errors that could / would lead to formation of the wrong concepts in a learner’s mind. Continue reading Thompson’s coax common mode explanation

An RF choke for a 1.8-30MHz coax power injector – LF1260 core

This article describes a prototype RF choke (RFC) for use in a power injector for 50Ω coax over range 1.8-30MHz. Power injector / extractors are often used to connect power and / or signalling on a shared common RF coax feed line to accessories such as remote antenna switches and ATUs.

Design criteria are:

  • Insertion VSWR of the RFC in shunt with 50+j0Ω < 1.1;
  • Dissipation < 2% of a 100W transmitter.

The core chose is a LF1260 ferrite suppression bead from Jaycar. It is a medium / high µ core readily available in Australia at $7.50 / 6.


Above is the prototype RFC wound with data cable wire for the purpose of measurement. In application it could be wound with 1mm enamelled copper or PTFE insulated wire (Curie point is lowish at 120°+, but it still benefits from higher temperature insulation). Continue reading An RF choke for a 1.8-30MHz coax power injector – LF1260 core

Riding the RF Gain control – part 4

This article continues on from Riding the RF Gain control – part 3 and explores the operating advice when applied to the next generation of receivers.

Direct sampling SDR

Lets jump a generation to the direct sampling SDR configuration.

In this category, I am covering receivers that do not convert the receive signal to an intermediate frequency, the ADC samples the signal at its off-air frequency.

The receivers may or may not have the following elements ahead of the ADC:

  • preamplifiers;
  • bandpass filters;
  • attenuators.

Because there may be no amplification prior to the ADC in some operating configurations, a voltage controlled attenuator may be used to prevent overflow of the ADC, this is the ‘analogue’ part of the AGC system. Continue reading Riding the RF Gain control – part 4