I have been asked whether the Field strength / receive power converter can be used to solve a Eb/N0 (Eb/N0) design problem.
Eb/N0 is a method often used for specifying the relationship of signal and noise that will give adequate bit error rate in a data demodulator.
Whilst the calculator was not specifically designed for that purpose, and you cannot directly enter the desired Eb/N0, with the help of a hand calculator for simple calculations, a solution can be found. Continue reading An example of Eb/N0 design with the Field strength / receive power converter
NEC-2 and NEC-4 support a GM card to translate and rotate a structure in three dimensions.
This article gives a simple but practical example of exploitation of this often overlooked facility. Continue reading Exploitation of NEC’s GM card
It has been apparent to me that the two local digipeaters often collide.
One uses UIDIGI and therefore is conformant with the p-persistence channel access algorithm.
The other is a Argent Data T3-135 which does its own thing.
To discover how many packets are detected with bad CRC, I installed 6PACK on a TNC. 6PACK reports receive CRC failures which are logged by the Linux kernel. Data was collected for seven hours through the middle of the day to ensure that there was traffic, but that channel utilisation was low. Continue reading Packet loss by digi collision
I have written on incompatibility of Argent Data TNCs with other devices.
In pursuing apparent packet loss, I have run up a Paccomm Tiny-2 MK-2 TNC with 6PACK firmware, and my aprx server using Linux AX25 kernel support and 6PACK driver.
It has become apparent that although the system reliably decodes packets from a multi-packet burst from VK2AMW-1, it only ever decodes the first packet of a multi-packet burst from VK2RHR-1. Frame check errors are logged. Continue reading Another Argent Data T3 incompatibility
An important element of early AX.25 networks was the Terminal Node Controller (TNC). Essentially, a TNC was a packet assembler / disassembler (PAD) pretty much equivalent to the PAD of X.25 networks but adapted to AX.25, and commonly, an embedded modem.
The TNC-2 was a hardware configuration which became a de-facto standard, and various firmware packages became available each with their own advantages and disadvantages. and a range of protocols for the host connection.
One of the inventions was the KISS protocol (KISS for keep it simple stupid) from Mike Chepponis (K3MC) & Phil Karn (KA9Q), and an implementation for TNC-2. Continue reading The KISS TNC – too simple, too stupid?
Chameleon has announced a small transmitting loop, the Chameleon CHA M-LOOP. Continue reading Chameleon CHA M-LOOP
I have posted several articles on headless APRS servers based on RPi. This article describes one based on RPi, AX25 soundmodem using a $2 USB sound card, and aprx v2.09.
Above is the server hardware. It uses the Sailer sound modem and kernel AX.25 support. This is currently configured as a RX only iGate for 30m, hence no tx audio path and no PTT (though on HF, PTT can be done simply using transceiver VOX). The small black USB module is a Belkin WLAN adapter. Continue reading RPi headless aprx server using soundmodem
I have a bit of a soft spot for the Diamond X-50N. It is a fairly rugged vertical for 2m/70cm. Though I live in a rural setting, I resist the temptation of high gain antennas of this type as they tend to suffer fatigue problems resulting in noise in quick time, whereas the rigid one piece X-50 seems to last and last (I have another that must have had 25 years outdoor service).
The X-50N is mounted on a telescopic steel mast at 11m at its base, and fed with 10m of LDF4-50A to the antenna entrance panel, and 2m of LMR-400 to the radio. The XN50N has three short radials which are visible in the pic above, but somewhat obscured by a fan of four upwards pointing wires to discourage birds perching on the gibbert for the G5RV. Continue reading Diamond X-50N #2 at VK2OMD
This article shows use of Lou Destefano’s (VK3AQZ) VK3AQZ RF power meter (RFPM1) to adjust the output power of a low power transmitter.
Above, the test setup used. Continue reading VK3AQZ RF power meter (RFPM1) – adjust Tx power example
This article shows use of Lou Destefano’s (VK3AQZ) VK3AQZ RF power meter (RFPM1) to plot the response of a 144MHz filter.
Above, the RFPM1 as used.
Above, the test setup. The filter (DUT) is connected between a standard signal generator (SSG), and the RFPM1 connected to the filter output. A DVM recorded the DC voltage on the ‘CAL’ terminals of the RFPM1. A series of measurements was made from 140 to 148MHz and the results calculated and plotted in Excel. Continue reading VK3AQZ RF power meter (RFPM1) – filter response example