Month: October 2020

RG6/U with CCS centre conductor – shielded twin study

Some online experts advise the use of synthesised shielded twin instead of ordinary two wire line for HF antennas claiming it is vastly superior.

Now it could be vastly superior for several reasons in all, but let’s focus on just one important parameter, loss under mismatch conditions.

The scenario then is the very popular 132′ multi band dipole:

  • the famous 40m (132′) centre fed dipole;
  • 20m of feed line being parallel RG6/U CCS quad shield with shields bonded at both ends;
  • 7MHz where we will assume dipole feed point impedance is ~4000+j0Ω.

We will consider the system balanced and only deal with differential currents.

Now rather than depend on loss calculators, most of which don’t reconcile with measurement of CCS RG6/U, I will used measured loss. RG6/U with CCS centre conductor at HF gives a chart of measured loss of a sample of commercial grade CCS quad shield coax.

Above is a comparison of matched line loss (MLL) based on measurement of a length of RG6/U Quad Shield CCS cable and prediction from Simsmith of Belden 8215 (also CCS). The ripple is due to measurement system error, measurements were made quite some years ago with a AIMuhf. Continue reading RG6/U with CCS centre conductor – shielded twin study

Last update: 21st November, 2020, 1:58 PM

nanoVNA – measuring cable velocity factor – demonstration – open wire line

The article nanoVNA – measuring cable velocity factor – demonstration demonstrated measurement of velocity factor of a section of coaxial transmission line. This article demonstrates the technique on a section of two wire copper line.

A significant difference in the two wire line is that we want the line to operate in balanced mode during the test, that there is insignificant common mode current. To that end, a balun will be used on the nanoVNA.

Above, the balun is a home made 1:4 balun that was at hand (the ratio is not too important as the fixture is calibrated at the balun secondary terminals). This balun is wound like a voltage balun, but the secondary is isolated from the input in that it does not have a ‘grounded’ centre tap. There is of course some distributed coupling, but the common mode impedance is very high at the frequencies being used for the test. Continue reading nanoVNA – measuring cable velocity factor – demonstration – open wire line

Last update: 28th October, 2020, 4:27 PM

ESP32 WROOM32 – A possible fix for failure of auto-program facility

Espressif’s esptool has a facility to automatically put the ESP32 into bootloader mode using the DTR and RTS signals of the serial interface.

For whatever reason, it is very unreliable. There are many schematics of knockoffs of Espressif’s original DevKits.

Above is the schematic of one of the larger makers of ESP32 modules, AI-Thinker. The auto-program facility is implemented in the logic gate arrangement at right top of the left top block. Continue reading ESP32 WROOM32 – A possible fix for failure of auto-program facility

Last update: 17th November, 2020, 2:10 PM

Battery contact corrosion on digital calipers

Corrosion of battery contacts in all manner of things due to leakage from the batteries is a growing problem as we seem to accumulate more and more devices that contain batteries and it becomes a chore to replace batteries by their expiry date.

Replacing batteries by their expiry date does not guarantee freedom from leakage related corrosion. The battery market is flooded with counterfeit product and it is hard to know what is genuine, even from apparently reputable suppliers.

Above is a cheap Chinese digital caliper that was damaged by leakage from a brand name (Duracell) SR44 cell. The characteristic green residue has been cleaned from the positive contact with an alcohol soaked cotton bud, and then the contact scratched with a Burgeon 2834C fibre glass scratch brush (below) to remove remaining corrosion products whilst vacuuming to extract as much of the residue as possible. Again, a wipe with a clean alcohol soaked cotton but leaves the contact as clean as practicable. These scratch brushes are extremely effective, one needs to avoid over use which removes more plating than desirable. Continue reading Battery contact corrosion on digital calipers

Last update: 27th October, 2020, 10:05 AM

Working a common mode scenario – VK2OMD – voltage balun solution

Recent articles Working a common mode scenario – G3TXQ Radcom May 2015 and Working a common mode scenario – G3TXQ Radcom May 2015 – voltage balun solution analysed a three terminal equivalent circuit for G3TXQ’s antenna system based on his measurements. Solutions were offered for the expected common mode current with no balun, with a medium impedance common mode choke (current balun) and an ideal voltage balun.

In summary, though G3TXQ expected the antenna system to have good balance, on measurement it was not all that good. The analysis showed that even a moderate impedance common mode choke reduced the common mode current Icm substantially more than no balun, or an ideal voltage balun.

This article performs similar analysis of the case of an ideal voltage balun applied to my own antenna system documented at Equivalent circuit of an antenna system at 3.6MHz.

In this article I will use notation consistent with (Schmidt nd).

Above is the equivalent circuit. Continue reading Working a common mode scenario – VK2OMD – voltage balun solution

Last update: 19th July, 2024, 2:29 AM

Working a common mode scenario – G3TXQ Radcom May 2015 – voltage balun solution

At (Hunt 2015) G3TXQ gave some measurements of his ‘balanced’ antenna system.

Above is Hunt’s equivalent circuit of his antenna system and transmitter. It is along the lines of (Schmidt nd) with different notation. Continue reading Working a common mode scenario – G3TXQ Radcom May 2015 – voltage balun solution

Last update: 24th February, 2022, 4:10 PM

Photo Voltaic Array – unbelievable efficiency from Chinese sellers

A friend recently purchased one of the many PV arrays advertised on eBay only to be disappointed.

A common metric used to evaluate cell technologies is conversion efficiency with 1000W/m^2 insolation. Most popular products are monocrystalline silicon technology which achieves 18-25% efficiency on an assumed 1000W/m^2 insolation.

If we look carefully at the above panel advertised as 200W, the active PV area is less than the frame size, probably \(A=0.93 \cdot 0.63=0.59 m^2\). We can calculate efficiency \(\eta=\frac{p_{out}}{1000 A}=\frac{200}{1000 \cdot 0.59}=34\%\), nearly double expected efficiency for monocrystalline cells. Continue reading Photo Voltaic Array – unbelievable efficiency from Chinese sellers

Last update: 14th October, 2020, 2:53 PM

A dipole centre insulator from HDPE cutting board

I made a small dipole centre insulator from 10mm HDPE cutting board on the CNC router. HDPE is moderately UV resistant so should survive for some years outdoors.

The insulator is 100mm across its widest points. No provision is made for supporting coax, it is for use with home made open wire line which will fall from the dipole leg ends. If you want to use it with coax or ribbon feedline, then incorporate a tab to secure those lines.

Continue reading A dipole centre insulator from HDPE cutting board

Last update: 30th December, 2020, 7:49 AM

Windows 10 – sound device Signal Enhancements

Recent versions of Windows 10 have made changes to some audio input processing.

Above is a screenshot of a Microphone Properties window, and attention is drawn to the section highlighted in pink which may appear in some devices.

The Signal Enhancements would appear to introduce certain non-linear behaviour.

I preface this with saying the ‘enhancements’ are probably hardware dependent (ie the chipset used and driver capability) but may also include Windows core, and this report applies to my specific configuration but hints issues that may be systemic.

That said, I performed a simple test switching an audio sine generator between two close frequencies and observed the level vs time in SpectrumLab.

The lower part of the screen is with ‘enhancement’ ON, the only change in the upper part is with ‘enhancement’ OFF. Continue reading Windows 10 – sound device Signal Enhancements

Last update: 12th October, 2020, 3:58 AM

nanoVNA – experts on improvised fixtures

A newbie wanting to measure a CB (27MHz) antenna with a UHF plug when his nanoVNA has an SMA connector sought advice of the collected experts on groups.io.

One expert advised that 100mm wire clip leads would work just fine. Another expert expanded on that with When lengths approach 1/20 of a wavelength in free space, you should consider and use more rigorous connections.

At Antenna analyser – what if the device under test does not have a coax plug on it? I discussed using clip leads and estimated for those shown that they behaved like a transmission line segment with Zo=200Ω and vf=0.8. Continue reading nanoVNA – experts on improvised fixtures

Last update: 9th October, 2020, 3:19 PM