AD9833 / PllLdr checkout

PllLdr is a generic microcontroller to load a PLL chip’s configuration registers using SPI. SPI is used by many PLL and DDS chips, data format and content varies from chip to chip.

This article documents checkout on an ADF9833 DDS chip.

The test was made on an inexpensive module purchased on eBay for about A$3 posted. This board has a 25MHz clock oscillator, but be aware they are sold with other frequencies as well, and is usable to about 40% of the clock frequency.

Above is the test board. It does not contain any form of output filtering, it really is bare bones. Continue reading AD9833 / PllLdr checkout

STC-1000 firmware change – STC-1000B

STC-1000 firmware change documented a chip and firmware update to a popular Chinese thermostat.

There has been enhanced firmware for a STC-1000 controller based on a PIC chip, but in my experience, most seem to be made with an STM8S003F3 chip. More recently, what appears to be a port of the PIC software to STM8 has been published at https://github.com/Emile666/stc1000_stm8.

The enhanced firmware is directed at home brewing for control of long running fermentation processes etc, incorporating storage for a number of multi-step programs (profiles). It is not really suited to more general applications like a fridge controller as for example it is more difficult for the common operation to set the set point.


This article describes a similar update to a later model STC-1000. Continue reading STC-1000 firmware change – STC-1000B

LED Driver measurement – #2

In the quest for drivers for some 18W LED plates, I have placed 6 orders for non dimming nominally 300mA drivers for 18-24W LED plates.

The LED drivers originally supplied with the LED plates were rated at 180mA (10.8W) and measured 150mA (9.0W)

The tests here use an 18W LED plate, wired as 18 pairs of 0.5W LEDs in series for a total voltage of around 60V and 300mA for 18W.

Most orders have not arrived after several months, it appears some Chinese sellers are not shipping even though they have said they did. One shipment contained a single bare board with no details, it wasn’t ordered and without ratings was consigned to the trash.

Above is a test of one type of LED driver rated at 300mA ±5%. It supplies 237mA which is 21% less than 300mA, hopelessly low on specification. The other four purchased were within 1% of the same current. Continue reading LED Driver measurement – #2

LED plate analysis – D44-22P-01

The D44-22P-01 is a Chinese LED plate rated at 15W and operates directly from 230VAC with an integrated driver.

It was purchased to explore the configuration of LEDs with integrated driver, and this driver looks deceptively simple.

The chips are JZ1009AE, a LED current driver. The 22 2835 LEDs are 9V LEDs for a string voltage of 200V. Continue reading LED plate analysis – D44-22P-01

Rigexpert Antscope2 – v1.1.1

A new version of Antscope2 has been released.

Online posters are excited that it supports some versions of nanoVNA, and one thread attempts to answer the questions:

The SWR image shows that the SWR minimum is at the center phase angle as you would expect. My question is:

  1. what are the other points that look like resonance,

  2. and should I trim my antenna based on phase?

  3. If so which one?

They are interesting questions which hint the ham obsession with resonance as an optimisation tartget.

Properly interpreting VNA or analyser measurements starts with truly understanding the statistic being interpreted.

In this case, the statistics being discussed are Phase and VSWR, and their relationship.

What is the Phase being discussed?

Above is an Antscope2 phase plot for an archived antenna measurement. The measurements are of a 146MHz quarter wave mobile antenna looking into about 4m of RG58C/U cable. We will come back to this. Continue reading Rigexpert Antscope2 – v1.1.1

Rigexpert AA-600 N connector dimensions

A recent post by David Knight described dimensional issues with the N connector on his AA-600 and problems with the seller in having it resolved.

Warned of a potential quality issue, I measured my own AA-600.

Above, the test of the inner pin forward surface distance from the reference plane on the N jack on the AA-600. The acceptable range on this gauge for the female connector is the red area, and it is comfortably within the red range.

Above is a table of critical dimensions for ‘ordinary’ (ie not precision) N type connectors from Amphenol.

This dimension is important, as if the centre pin protrudes too much, it may damage the mating connector.

Pleased to say mine is ok, FP at 0.192″.

I used a purpose made gauge to check this, but it can be done with care with a digital caliper (or dial caliper or vernier caliper), that is what I did for decades before acquiring the dial gauge above.

AIM4170 – de-embedding the feed line in remote measurement – a simple match

At AIM4170 – de-embedding the feed line in remote measurement a set of measurements of a monoband antenna looking from the transmitter were analysed to de-embed the feed line and arrive at the indicated feed point impedance.

This article explores a simple series match to improve the load seen by the transmitter.

In the Simsmith model above, the estimated feed point impedance is imported into element L, then a series section of lossless 50Ω line to represent the coax in the common mode choke (balun), then a series section of lossless 75Ω to perform the impedance transformation, then a section of 50Ω lossless line to make up the required length to the transmitter. Continue reading AIM4170 – de-embedding the feed line in remote measurement – a simple match

AIM4170 – de-embedding the feed line in remote measurement

At nanoVNA-H – de-embedding the feed line in remote measurement I recently wrote on a procedure that can be very useful to refer measurements made at the transmitter end of a feed line to the antenna feed point.

A correspondent recently shared an AIM 4170 scan file of his 40m half wave dipole antenna system taken from the transmitter end of the coax and maintaining the common mode current path by bonding the shield of the coax connector to normal connection point on the transmitter.

Above is his graphic of the measurement looking into around 23m of RG58 feed line.

It shows the VSWR curve is quite classic in shape, the frequency of minimum VSWR is a little low, and the minimum VSWR is 1.478 which is quite within expectations of such an antenna. Continue reading AIM4170 – de-embedding the feed line in remote measurement